STEEL TRUSS STRAIGHT TRACK
Description
- By plane made entirely of stainless steel.
- Profile of the track formed by a lattice made of stainless steel tube, which allows the use of such means for loads up to 1750 kg.
- Support of the lattice path by both lift rods forged or structure, depending on the facility, with a separation distance of 1600 mm.
- Design via Mecanova compatible equipment.
- Via compatible with automatic movement of racks in the facility such as the "tractorinos. "
- Welded finish by acid pickling.
- Remove support structure.
- High resistance to corrosion.
CURVE 90º TRACK STEEL LATTICE
Description
Curve 90º track brand stainless steel lattice Mecanova with load capacity of 1200kg sags supported by stainless steel.
MANUAL CHANGE OF ADDRESS ROUTE 2 STAINLESS
Description
- Change made entirely of stainless steel.
- Allows branch line air network in two perpendicular directions, right or left, through a wedge-shaped piece.
- Operated by manual needle with handle
3-WAY TIRE CHANGE VÍAINOXIDABLE
Description:
- Change made entirely of stainless steel.
- Allows branch line air network in three perpendicular directions, regardless of the direction in which change is between using a wedge-shaped piece.
- Operated by pneumatic cylinder.
ALUMINUM STRAIGHT TRACK DOUBLE RAIL
Description:
- Profile airway consists of extruded aluminum alloy 6063 with treatment of T-5 temper.
- Moment of inertia of the double rail track equal to 46.44 cm4 Road section designed to allow the cars rolling over it transport while facilitating the installation of the necessary elements for fixing it.
- Holding the beam via a support structure with cast aluminum saddle, whose resistance to fracture obtained by mechanical testing has a minimum value of 2,240 kg.
- Fasteners for the saddle to the support beam made of stainless steel AISI-304.
- Screws in stainless steel AISI-304.
Legal Requirements:
- Screws according to DIN.
- Dimensional tolerances road alignment according to UNE 30.0.
- Treatment of T-5 temper road profile according to UNE-EN 755-2: 1998.
- Alloy of the saddle as 1st 38252 UNE review.
Volunteer Requirements:
- High resistance to corrosion.
- Easy installation.
- General separation equal to 600 mm saddle.
CURVE 90º TRACK ALUMINUM double rail
Description
Airway profile consists of extruded aluminum alloy 6063 with treatment of T-5 temper. Moment of inertia of the double rail track equal to 46.44 cm4
Legal Requirements
- Screws according to DIN.
- Dimensional tolerances road alignment according to UNE 30.0.
- Treatment of T-5 temper road profile according to UNE-EN 755-2: 1998.
- Alloy of the saddle as 1st 38252 UNE review.
Volunteer Requirements
- High resistance to corrosion.
- Easy installation.
- Separation of saddles general equal to 600 mm.
MANUAL CHANGE OF ADDRESS WITH NEEDLES 2 ALUMINUM
Description:
Airway profile consists of extruded aluminum alloy 6063 with treatment of T-5 temper. Moment of inertia of the double rail track equal to 46.44 cm4. Includes manually operated needles with handles.
Legal Requirements
- Alloy of the saddle as 1st 38252 UNE review.
- Dimensional tolerances track profile according to UNE 30.066.89/ISO 6362-4.
- Treatment of T-5 temper road profile according to UNE-EN 755-2: 1998.
3-WAY MANUAL CHANGE OF ALUMINUM WITH NEEDLES
Description:
Airway profile consists of extruded aluminum alloy 6063 with treatment of T-5 temper. Moment of inertia of the double rail track equal to 46.44 cm4. Stainless steel screws stainless steel AISI-304.
Legal Requirements.
- Screws according to DIN.
- Alloy of the saddle as 1st 38252 UNE review.
- Dimensional tolerances road alignment according to UNE 30.066.89/ISO 6362-4.
- Treatment of T-5 temper road profile according to UNE-EN 755-2: 1998.
+ Budget Request
